How to handle the wooden floor bulging due to flooding in the rainy season

Wood flooring is a very hydrophobic material and will often be blistered, warped if soaked in water. So how should it be handled?

During the time of using the wooden floor, you cannot avoid spilling water on the floor despite being very careful. Especially in the rainy season, the prolonged heavy rain often causes flooding. After each round like that, you need to know how to handle the bulky wooden floor, otherwise it will have to suffer a lot of economic losses when you have to replace your entire floor.

Flooded wooden floors in the rainy season.

Depending on the type of wood floor, the degree of damage will vary and the treatment will not be the same. Let's find out right away how to overcome the situation of natural wood floors or industrial wood floors are absorbed.

1. How to handle natural wood floors is blistering due to water absorption

Natural wood is usually of good quality, high durability but still cannot avoid blistering due to water infiltration, especially when being soaked in dirty water during the rainy season due to inundation in lowland areas.

Natural wood flooring has a better quality.

When spilling water on a wooden floor and letting it seep into the interior, you need to proceed immediately with effective measures to limit the harm. First, you need to remove the water layer on the surface of the wooden floor by using a soft cloth soaked in water . Avoid the use of hard, dry, and ragged cloths as this will scratch the surface of your natural wood floor. After you have drained the water and dried the floor surface, the next step is to treat the water that has been absorbed below by using an electric fan that blows until the water under the floor evaporates.

Use a soft cloth to dry off the surface of the wooden floor.

However, if the wooden floor is soaked in water for too long and too much water is absorbed, such as in flooded storms, for example, the treatment of the wooden floor is more difficult. Natural wood will normally be inflated due to hydration but when the water evaporates, it will return to its original state. Too much water makes the natural wood floor bulge because it has expanded beyond the limit. To process, you need to follow these steps:

1. Carry out moving all kinds of furniture in the house and remove one side of the wooden splint near the wall, choose the splint along the length of the wood pieces.
2. The next step in how to handle the inflated wooden floor is to use an electric fan to blow the water to evaporate.Just blow like that regularly for about 5-7 days, when the wooden floor is completely dry, it will return to its original state.
3. After the wooden floor is dry and normal, reinstall the removed wooden splints.Except in cases of poor quality wood flooring, too heavy water infiltration is difficult to overcome.At that time, you only have two choices: continue to use or replace blisters with a new wooden floor.

To minimize the situation of curving, warping, blistering, when installing wooden floors, you should leave a small space near the foot of the wall (about 10 - 12mm) so that the wooden floor has space to expand when being soaked. ok

2. For laminate flooring

Laminate flooring has a four-layer structure with varying degrees of expansion, so it often has poor quality and water resistance is much lower than natural wood flooring. Moreover, when being soaked in water, this kind of wood flooring is harder to dry because both the top and bottom of it are covered so the water can only escape from the two sides of the wood.

Laminate flooring.

Therefore, if the laminate flooring is soaked in water for a short time, you will have the opportunity to disassemble the wood to wipe and dry , but if it is flooded for too long in the rainy season, it is difficult to handle reason and bring it back to normal, but must be completely replaced.

However, there are still many types of industrial floors with good quality and water resistance. At that time, you can proceed to handle when the wooden floor is bulky similar to how to handle natural wood flooring. Accordingly, you only need to remove all the water on the surface, then disassemble the wood pieces to dry and then re-install and continue using as usual.

Remove the wooden tops to dry.

3. Note when handling wooden floors that are flooded

1. As soon as the wood floor is submerged and water is absorbed, you need to dry the surface and remove the wood pieces as soon as possible. In the case of flooding due to storms, you proceed immediately after the sprint.
2. Use only fans or air conditioners to dry the wooden floor, absolutely not to dry, especially at high temperature and not to be sunlit.
3. If the swelling and blistering condition is too heavy, you should not arbitrarily handle it but should contact the construction unit to assist them in processing immediately by professional operations.

Contact the construction unit to process immediately.

Above is how to deal with wooden floors that are bloated due to water infiltration in the rainy season for both natural wood flooring and laminate flooring. Hopefully with this guide, you already know how to cope with protecting your family's assets.